Pololu QTR-8A Reflectance Sensor Array
Description
- Infrared phototransistor based reflectance sensor array
- 3.3V to 5V operation
- Measures only 2.95" x 0.5" x 0.125" and weighs 3.09 grams
The Pololu QTR-8A Reflectance Sensor Array has 8 IR LED/phototransistor pairs mounted on a 0.375" pitch, making it a great detector for a line-following robot. Pairs of LEDs are arranged in series to halve current consumption, and a MOSFET allows the LEDs to be turned off for additional sensing or power-savings options. Each sensor provides a separate analog voltage output.

The QTR-8A reflectance sensor array is intended as a line sensor, but it can be used as a general-purpose proximity or reflectance sensor. The module is a convenient carrier for eight IR emitter and receiver (phototransistor) pairs evenly spaced at intervals of 0.375" (9.525 mm). Each phototransistor is connected to a pull-up resistor to form a voltage divider that produces an analog voltage output between 0 V and VIN (which is typically 5 V) as a function of the reflected IR. Lower output voltage is an indication of greater reflection.
The outputs are all independent, but the LEDs are arranged in pairs to halve current consumption. The LEDs are controlled by a MOSFET with a gate normally pulled high, allowing the LEDs to be turned off by setting the MOSFET gate to a low voltage. Turning the LEDs off might be advantageous for limiting power consumption when the sensors are not in use or for varying the effective brightness of the LEDs through PWM control.
The LED current-limiting resistors for 5 V operation are arranged in two stages; this allows a simple bypass of one stage to enable operation at 3.3 V. The LED current is approximately 20-25 mA, making the total board consumption just under 100 mA.
Breaking the Module in Two:
If you don't need or cannot fit all eight sensors, you can break off two sensors and still use all 8 sensors as two separate modules, as shown above. The PCB can be scored from both sides along the perforation and then bent until it snaps apart. Each of the two resulting pieces will function as an independent line sensor.
- This module ships with a 25-pin 0.1" header strip and a 100 Ohm through-hole resistor as shown above
- Size: 2.95'' x 0.5'' x 0.125'' (without Header Pins installed)
- Weight without Header Pins: 0.11oz (3.09g)
- Operating Voltage: 3.3-5.0V
- Supply Current: 100mA
- Output Format: 8 Analog Voltages
- Output Voltage Range: 0V to supplied voltage
- Optimal Sensing Distance: 0.125" (3 mm)
- Maximum Recommended Sensing Distance: 0.25" (6 mm)
I have bought this product for an arduino line follower robot and its working perfect!
I recommend the purchase, great product ensures excellent reading. We used it on our Wickedbotz / Brazil team line follower
This sensor module has 8 IR LED/phototransistor pairs, each sensor provides a separate analog voltage output. You can break off two sensors and still use all 8 sensors as two separate modules. Really good for line follower robots.
Estimate shipping
Refund Policy
If you are not satisfied with a product purchased from the Site, you may request a return within 30 days from the delivery date, unless the product is listed under the Return Exceptions below or is subject to specific return conditions noted on the product page.
This return policy also applies, as a minimum standard, to products sold and fulfilled by third-party vendors through the Marketplace.
Please review the Return Conditions, Return Exceptions and the process on How to Request a Return Authorisation (RA) before initiating a return request.
United Kingdom consumers exercising their statutory Right of Cancellation are subject to different conditions. See the Statutory Right of Cancellation.
Returns under this policy concern non-defective products. In the case of a confirmed manufacturing defect, remedies are handled under the Warranty terms, at the Vendor's discretion. See the Warranty section.
Return Conditions
To qualify for a refund under the 30-day return policy, all of the following conditions must be met:
- A valid Return Authorisation (RA) number must be obtained prior to returning the product. Returns without an RA number will be refused.
- The RA number is valid for 30 days. The returned item must be received within that period.
- The RA number must be included with the return.
- Products must be returned in unused, unmodified condition (e.g., no scratches, alterations, missing parts, or signs of installation/use) and in their original packaging, suitable for resale.
- Shipping fees are non-refundable. Return shipping costs are the responsibility of the customer, except in cases of a product confirmed defective through RobotShop's troubleshooting process or of a verified shipping error by RobotShop.
- Refunds are processed within 7 days after receipt and inspection of the returned item.
- A £100 cleaning fee may apply to domestic robots returned in used or unclean condition.
- A 20% restocking fee may apply to large-quantity returns of items ordered specifically for the customer from the manufacturer or not part of RobotShop's standard inventory.
Return Exceptions
The following products are not eligible for return or refund under this policy:
- Used, damaged, or modified products — Items that show signs of use, wear, or alteration, making them unsuitable for resale.
- Consumables * — Use and wear-and-tear components, altered or depleted through use (e.g., batteries, belts, brushes, gears, filament, tyres, disposable bags, lubricants, greases, waxes, etc.). Not eligible for return once opened or used.
- Perishables — Goods liable to deteriorate or expire rapidly. Not eligible for return.
- Sealed goods (health or hygiene) — Items sealed for health-protection or hygiene reasons (e.g., masks, gloves, odour-absorbing products). Not eligible for return once unsealed.
- Build-it-yourself products and items requiring customer assembly * — Including robots & kits, robot parts, and other products requiring assembly or soldering. Not eligible for return once assembled, soldered, or installed.
- Digital Goods, Software, and Apps * — Final sale only, due to licensing restrictions.
- Clearance Items * — Products identified as clearance or final sale, including end-of-life or discontinued items.
- Custom-made, personalized, or special-order items — Products manufactured, configured, adapted, or built to the customer's own specifications and requirements.
- On-Demand Items * — Standard catalogue products not stocked by RobotShop and ordered specifically to fulfil a customer request.
- Professional & Specialized Equipment — See the Professional & Specialized Equipment Warranty page and Professional & Institutional Buyers (B2B) section in the Terms & Conditions.
* United-Kingdom consumers retain their statutory Right of Cancellation on these items. Its exercise is subject to the conditions and exclusions set out in the Statutory Right of Cancellation, and any reimbursement may be reduced to reflect a loss in value resulting from handling beyond inspection.
How to Request a Return Authorisation (RA)
While the same return policy applies, these orders require a separate contact process for returns.
- RobotShop Fulfilled Orders → submit a support ticket from your account under My Support Tickets.
- Marketplace Vendor Orders → submit a ticket from your account under My Marketplace Tickets to contact the vendor directly.
Note: Marketplace vendor products are normally labelled with SKUs starting with RM, and identified on the product page with the mention "Sold and fulfilled by [Vendor Name]".